Victron Energy SmartSolar Charge Controller MPPT RS 450/100-Tr with Bluetooth #NI060623

NOTE: This charge controller is for 48V systems. When designing for PV array open circuit voltage. The maximum open circuit voltage of the PV array must be less than 8 times the configured float voltage. Where the array voltage exceeds this parameter, the system will give an "Over-charge Protection" error and shut down. 450V is the extreme maximum voltage, anything above 450V will cause permanent damage to the product.

• Maximum charge current: 100 Amp
• Maximum DC PV Voltage: 450 V
• MPPT operation voltage range: 80-450 V
• Number of trackers: 2
• Weight: 17.4
• Dimensions: 17.3" x 12.3" x 4.96"

• Victron Energy SmartSolar MPPT RS is a 48 V Solar charge controller with up to 450 VDC PV input and 100 amp output. It is used in on-grid and off-grid solar applications where maximum battery charging power is required
• Victron Energy SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect App
• Daisy Chain Additional Units: Victron Energy SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply daisy chained to each other with an RJ45 cable
• Victron Energy SmartSolar RS charge controller is equipped with a display on the front panel. The display reads battery volts, charge current and voltages from both array’s individually including instantaneous and total figures and unit status including any possible error codes
• Victron Energy SmartSolar RS charge controller is equipped with a programmable relay and options for remote temperature and voltage sensing. The remote input can accept the Victron Energy smallBMS and other types of Victron Energy BMS with allow-to-charge signals
• Battery Charger
• DC-AC Invertrs
• Combined Inverter/Chargers
• DC-DC Converters
• Isolation Transformers
• Batteries
• Battery Monitors
• Diode and FET Splitters

Specifications:

• Charger:
  • Programmable charge voltage range: Minimum: 36 V, Maximum: 60 V (8)
  • Charge voltage ‘absorption: Default, 57.6 V (adjustable)
  • Charge voltage 'float': Default, 2 V (adjustable)
  • Maximum charge current: 100 A
  • Battery temperature sensor: Included
  • Battery voltage sense: Yes
• Solar:
  • Maximum DC PV voltage: 450 V
  • Start-up voltage: 120 V
  • MPPT operating voltage range: 80 – 450 V (1)
  • Number of MPP Trackers: 2
  • Maximum operational PV input current: 18 A per tracker
  • PV short circuit current reverse polarity protection (2): 20 A per tracker
  • Maximum DC output charging power:  4000 W per tracker,  5760 W total
  • Maximum PV array size per tracker (3): 7200 Wp (450 V x 20 A)
  • PV Isolation fail level (4): 100 kΩ
• General: 
  • Synchronized Parallel Operation: Yes, up to 25 units with VE.Can
  • Programmable relay (5): Yes
  • Protection (6): c, d, e
  • Data Communications: VE.Direct port, VE.Can port & SmartSolar Bluetooth (7)
  • Bluetooth frequency: 2402 – 2480 MHz
  • Bluetooth power: 4dBm
  • General purpose analog/digital in port: Yes, 2x
  • Remote on-off: Yes
  • Operating temperature range: -40 to +60°C (fan assisted cooling)
  • Humidity (non-condensing): max 95%
  • Environmental condition: Indoor type 1, conditioned
  • Suitable for wet locations: No
  • Pollution degree: PD2
  • Maximum altitude: 2000m
  • Over voltage category: OVCII